Related topics

5
SYS, it is wise to make a backup copy first; if anything goes terribly wrong you can begin again at a known point. Why is Watstar so slow? Improper settings might be detected by comparing the /z number to the following table of relative processor speeds: (approx.) 386/33 20 486/33 36 P100 185 386/40 24 486/40

Linux Frequently Asked Questions with Answers (FAQ: 2/2)
The on-board video is automatically disabled when an add-on card is detected at startup. Another consideration for choosing against the NF7-M's on-board video I'm not interested in processor speed so much as I'm limited by how fast I can work with the PhotoShop tools. My primary benefit for using the NF7-M is

PB450 CPU Upgrade
The wrong interrupt is detected. The NE2000 is at < >IRQ-15 but Linux is detecting IRQ-7 which belongs to the the printer. When < >booting up with a slower bus speed, or with a slower processor speed. the IRQ < >is detected properly but then there's some sort of framing errors reported by the kernel for the < >eth0

Windows XP tree not found
1.2 What will happen if an extraterrestrial signal is detected? 1.3 How is data collected from the telescope and transmitted to other machines for analysis? ..... per FLOP (from table) MHz = processor speed in MHz For example, a 350 MHz Pentium II is expected to process one work unit in 555 (8.0 / 350) = 12.69 hours.

News, 29-30/11/99
Note that a runt name is still detected and reported as an NTP event and on the debug trace. in debug mode i dont think protection from clogging really matters. ..... in the late 70s to tens of nanoseconds now, I expect these issues will not go away, and accuracy expectations will scale with processor speed.

X1541 Cable Problems
Original Message ----- From: "Sky McKinley" <s...@pdx.edu> To: <m...@openbsd.org> Sent: Thursday, September 12, 2002 13:34 Subject: Wrong processor speed detected Hi. I'm running 3.1-stable on a Toshiba laptop with a 1 GHz processor. Occasionally, dmesg shows that I have a 731 GHz processor. Why would this happen?

Distros for older hardware
MIPS stands for (depending who you listen to) Millions of Instructions per Second, or Meaningless Indication of Processor Speed. ..... Amongst other things, its job is to flush the read buffer when it detects a disk change on the floppy disk drive: VFS: Disk change detected on device 2/0

G6-SYSTEM BIOS FIX FOR GATEWAY VENUS BOARD!!!
VFS: Disk change detected on device 2/0 ---------------------------------------------------------------------- 8.5 What is devfs and what does it do? The devfs implements a new way of MIPS stands for (depending who you listen to) Millions of Instructions per Second, or Meaningless Indication of Processor Speed.

Windows XP Processor Speed
Digital Alpha EBP20-AA mainboard (also known as NoName) (It's the AT-style keyboard version) Processor ID: 21066 Processor Revision: 2 Processor speed: 166.66 What am I doing wrong???? I tried: one 2,1 partition one 10Mb partion and the rest empty no partions at all. I made the partition in my pentium using dos

help~~vp2
... im sorry im not much help the only thing i know is that installing as a standard PC will fix this but thats not a good solution... when the processor speed is detected wrong this way it causes the menus to fade faster dont know if youve noticed, and also causes some programs problems with timing and makes games

Linux Frequently Asked Questions with Answers (FAQ: 2/2)
I suspect the culprit is ZoneAlarm...it seems to happen when a lot of "intrusions" are detected. Any ideas? "Ken Blake" <kbl...@nospam.com> wrote in message with how much RAM they have or with all the things that might be considered 'resources' in general--things like hard disk space, processor speed, etc.

WMI not reporting CPU speed correctly
Before this, if I started up under battery power it would run with a slow processor i don't mind running slower on battery power for extended battery life, but i'm running on AC right now, and that's where i don't want to run at a reduced speed, but under AC i got the Detected 172.960 MHz processor. message (i

Joseph K Please read and respond.
\uffff Processor Speed = 648 MHz Baud rate is 9600 8 Data bits, 1 stop bits, no parity (configured from lom) Firmware CORE Sun Microsystems, Inc. @(#) core .... GEOM_MIRROR: Device gm0e: provider da0e detected. GEOM_MIRROR: Device gm0a: provider da1a detected. GEOM_MIRROR: Device gm0a: provider da1a activated.

Seti@home alt.sci.set/sci.astro.seti FAQ ver. 1.11
Did I remove the wrong key, or should I boot to the Win98 startup disk and run setup that way? Thanks. I recently installed a Soyo 6BA+IV motherboard and used my existing PII 266 as the processor. When I check the processor speed in McAfee, it says that my processor is running at 66 mHz.

OS/2 2.0 REVIEW
Mark Kettner (kett...@cat.et.tudelft.nl) reports that his system was capable of running my memory test for 2300 times faultlessly, but then detected around As for some speeds the motherboard is only stressed HARDER for a slower processor speed, (120 MHz-> motherboard runs at 60MHz, 100MHz-> motherboard runs at

NoName AXPpci 33 & 2,1 EIDE Disk????? part II
What is "yet another 20 detected ISDN cards" worth for Williams? Yes, Linux for example is modularized. But even stuff like file-systems that bear .... Of course there is some minimum processor speed. Proof: there are n sound channels with quality XX you want to mix. You need to accomplish it in YYY msec,

Wrong processor speed detected
I haven't fired that box up for a while and the processor speed was what I recollected, but I could be wrong there. On my aging 266MHz Thinkpad600 (there, that ought to make you feel better =) I added RAM that exceeded the tech doc's specs. It surprised me when the BIOS detected it, and different liveCDs recognized

gmirror, sparc and SCSI problems
Plus, there are a LOT of other things that go wrong, too, all of which you end up replacing the main board for. As for your second note on this, I think I'd rather have 'em work on SMP (and I say this as someone who considers SMP a rather nitch design -- processor speed increases *so* rapidly that usually

detect wrong processor speed?
According to Crucial Memory's website, the Compaq Deskpro XE 566mhz(they list by processor speed) takes PC133 *non-parity* SDRAM. It was giving a "Memory parity error detected system halted" error and the owner has now, under the expert guidance of my brother :-> proceeded to format her HD.

Wrong processor speed detected
The hardware requirements (memory, disk space, and processor speed) for OS/2 2.0 are much greater than MS Windows 3.1 for the same level of performance. ..... Diskcopy (A: A:) from OS/2 command line: if target diskette is wrong density or write-protected, the copy is ended and you have to start over (reading source